0 Members and 1 Guest are viewing this topic.
This machine is based on gravity power and seesaw system.We can make it more simple .As per sketch there will be two seesaw system and both will be attached with a stand.This stand will work to hold the seesaw.There will a middle track(MIDDLE TRACK SEESAW) which will work a pathway to transport the object from one seesaw to another seesaw.there will be two motors which will work to inclined the both side seesaw systems by pushing the counter weight side of each seesaw.When right side motor will work to push up the counter weight Arm of seesaw then it will be inclined and object will get start to move towards left side and arrived on the left side seesaw and now left side motor will work to push the counter weight side arm to inclined the seesaw and object will move towards right side.In this way each seesaw will work by their turn.I would like to insist on some following point.(1) The Stand will work to hold the counter weight so that the seesaw couldn't be imbalanced after unloading the object.(2) we can set up a generator under the counter weight to generate energy or can get gain due to kinetic energy of ball..(3)the length of middle track will be less than the length of arm of seesaws.(4)The motors will work to push the counter weights towards upside .(5)we can take the object(Rolling Ball) mass from 100 to 1000 kilogram or more as we all know that if a seesaw is balanced then we can lift up or lift down it even with the power of our finger tips .I would also like to attract your attention on a mechanical advantage of rolling ball and its distance from fulcrum.When motor will lift up the counter weight arm of seesaw and ball will get rolling down then the rolling ball will also apply a force as it will move further from fulcrum.(6)The middle track will also work like a SEESAW system and will work as a bridge to fill the gap between Left and Right side seesaw when seesaws will be inclined.The middle track seesaw either get energy from a motor or directly connected with both side seesaw when counter weight arm will be lift up then this arm will also work to lift up the second part of middle seesaw and middle track Arm will be come down to work as a bridge.(7) This design will work as a free energy device .The counter weight arm of both side seesaws will work to generate electricity when this counter weight arm will hit the piston generator then the generator will work to produce energy.(8)Friction will be not an issue in this design BECAUSE THE LENGTH OF MIDDLE TRACK WILL BE very LESS THAN BENT ARMS AND ABOVE ALL DEPEND THE VELOCITY OF BALL.(9) Use potential energy formula when stand attached with counter weight (100 kilogram) will hit the piston generator and motor works to lift up the seesaw up to 20 centimeter.P.E.=mghP.E.=100*10*.20=200jouleThe out put will be 200joule but input will be only 10 to 15 joule by motors as we all know that IF A SEESAW IS IN BALANCED POSITION NO MATTER HOW MUCH IT IS HEAVY,THEN THERE WILL BE NEED OF VERY VERY LESS FORCE TO MOVE IT OR MOVE DOWN.IN THIS WAY THIS SYSTEM WILL WORK.THE VELOCITY OR KINETIC ENERGY OF BALL WILL BE ALSO USEFUL TO GENERATE ENERGY WHILE IT WILL BE ROLLING DOWN ON CURVED SURFACE OF LEFT SIDE SEESAW .(10) The main point in this design is only input force ,that is very very less and the rest work will be done by gravity itself.(11)I have done several experiments on it to know the feasibility of this design and my experiments clearly shows me that it must work .there is No doubt regarding the feasibility of this design even I'm VERY MUCH surprised that physics laws are playing a supportive role in this design.(12) Thermodynamics laws will not work in this design.Inertia ,friction is not a problem in this design.Thank you Sir!Vikram kumar GuptaB-242,JeedimetlaHyderabadIndiaPh.No.+918106163023
The ball will not jammed as the middle track seesaw will work as a bridge to transport the ball towards left seesaw.second the left seesaw also has a counterbalance.see the diagrams carefully.third can you please send me your email so that I could send diagram as I had to post diagrams due to file size restriction.my email. vikram_gupta11@rediffmail.com
See this new diagram.
I also did an experiment I put a 2 kilogram weight ball on a beam and counter weight and make a hole in the middle of the seesaw to balanced it. I applied only just very minimal force on the counter weight arm of this seesaw to tilt it down and ball get started rolling down due to gravity .The ball traveled upto 3 meter distance on the flat surface but when the counter weight side arm came down it badly hit my hand like a hammer .So now tell me what is this .Is it not perpetual motion that the out put is more than input?
It is very much cleared that you don't have knowledge about Archimedes principles. and not understood it.The velocity of ball depends on the length of the seesaw arm.when the seesaw will be tilted down then the ball get started rolling down ,but a middle track seesaw will work to direct it towards left seesaw as it will work like a bridge.there is not a single flaw in this design .if you see the diagrams very carefully then you will find that the gravity will work here due to curved arms.I have done experiments on it and it works .it will be better for you that you please read Archimedes laws and post your comments .Read each points carefully with sketch and you will find that there is no flaw in this design.I would like to tell you that I have consulted with a very renowned physics professor and he is also agree with me that there is no flaw in it and it must must work as he could'nt find any flaw.It is completely a flawless design.Friction is not an issue in this design and as I did experiments with a rough surface wooden track.I think you should consult with your seniors and they will tell you that this is completely flawless.Just do a simple experiment .Take a ball and two tracks and now only inclined only one track but remember it shouldn't be touch with second track.Now put a third track between these twp tracks and release the ball from the top of first track.you will find that the ball will travel long distance .Now consider about curved arms and input .Your all unimportant doubts will be cleared immediately.